How Much Does a Paver Weigh?

Find the weight of a paver by material and size, then scale it up to per-square-foot, per-pallet, and full-project totals — with pickup-truck payload limits and safe-handling thresholds built in.

Paver Weight by Material and Size

Material and thickness drive per-piece weight more than footprint alone. Concrete pavers follow the ASTM C936 dimensional standard referenced in CMHA PAV-TEC-002, with a typical concrete density around 130 lb per cubic foot; natural stone varies widely by species and cut thickness. The table below covers the common categories at standard install depths.

Note the per-square-foot column: a large-format 80mm paver weighs more per piece (~40 lb) but slightly less per square foot than a 60mm because its face area is large relative to its thickness. Natural stone is the outlier — its higher density (~160–175 lb per cubic foot vs concrete's 130) makes it the heaviest option both per piece and per square foot.

How to Calculate Total Project Paver Weight

Total project weight tells you how many pallets to order, whether your truck can carry them, and whether an elevated deck can support them. The math is three steps:

Worked example — 200 sqft patio. A 20 ft × 10 ft patio in standard 60mm Holland Stone (~5 lb each):

That 4,500 lb is paver material only — base aggregate and bedding sand add substantial tonnage on top. At 540 pavers per pallet (Belgard Holland Stone), 900 pavers is about 1.7 pallets, so you would order 2 pallets at roughly 3,060 lb each — about 6,120 lb of delivered material. For the base layer under those pavers, use the Paver Base Calculator; for the full paver count on any patio shape, start with the Paver Weight Calculator.

Pallet Weight and Pickup Truck Payload

A full paver pallet weighs 2,900–3,100 lb — heavier than most half-ton pickups can legally carry. The number that matters is your truck's payload (Gross Vehicle Weight Rating minus curb weight), printed on the door-jamb sticker. Verify your specific truck's payload sticker before loading — nameplate class is only a rough guide.

A two-pallet order at roughly 6,000+ lb combined needs a flatbed delivery truck with forklift offload. If forklift access is blocked, the driver stages the pallet at the curb — leaving you to hand-carry 3,000+ lb to the work area. Confirm 10–12 ft of clear width with your supplier before scheduling.

Brand Comparison: Belgard, Pavestone, and Cambridge Pallet Weights

Pallet weight varies by brand even when the nominal paver size is identical, because pieces-per-pallet and product mix differ. Values below are for 60mm Holland-style products unless noted; per-piece weight is the pallet weight divided by piece count.

For truck-payload sizing, take the upper bound of the published range — 3,060 lb for Belgard Holland, 2,884 lb for Pavestone Holland, 2,715 lb for Cambridge — so a ±5% regional-plant variance does not push you over your GVWR. The Belgard Mega-Arbel at 35–41 lb per piece is the key handling threshold: pieces at the top of that range approach the industry-cited safe-handling guideline of about 50 lb single-person for loads that require twisting or reaching, so plan a vacuum lifter or a two-person carry. For large-format and heavy natural stone, the Patio Stone Calculator covers coverage and base depth.

Paver Weight on Elevated Decks and Rooftops

Ground-level patios carry their weight straight to soil, so total tonnage is a delivery problem, not a structural one. Elevated patios — over a deck, garage, or roof — are different. Residential floor live load is commonly benchmarked near 40 psf, but the locally adopted code edition controls; verify the live-load requirement for your project with your local building department. A 2-in concrete paver alone is only ~22–25 psf, but the full base stack is the problem: a 2-in paver + 1-in bedding sand + 4-in compacted aggregate totals roughly 80–87 psf — about double a typical 40-psf residential benchmark. Rooftop paver systems use pedestal-mount or thin-set methods (no gravel base) to hold dead load near 22–25 psf, and require review by a licensed structural engineer before installation.

Paver Pallet and Delivery Cost

As of early 2026, concrete paver pallets run approximately $300–$800 per pallet (covering 100–160 sqft), with local flatbed delivery adding roughly $80–$200 per pallet including forklift offload. Prices vary significantly by region and season — verify with your local supplier before ordering. A 400 sqft patio needs about 3–4 pallets, putting delivery alone in the $240–$800 range depending on distance and access.

Safe Handling and Two-Person-Carry Thresholds

NIOSH publishes a lifting equation with a maximum recommended single-person load of approximately 51 lb under ideal conditions (upright posture, load held close, no twisting). Treat that as an industry-cited guideline, not a hard limit: real paver work — kneeling, twisting, reaching over a screeded bed — lowers the safe threshold. Standard 4×8 concrete pavers (4–6 lb) are well within solo range; a Belgard Mega-Arbel (35–41 lb) or a natural-stone slab (up to ~36 lb) approaches the two-person threshold under those conditions. Handling guidelines also vary by employer policy and state OSHA-plan adoption — confirm the rules that apply to your site.

Paver Weight and Transport Checklist

Run these five checks before and during delivery to avoid overloaded trucks, blocked forklifts, and back injuries:

1. Calculate total project weight before ordering. Paver count × per-piece weight ÷ 2,000 = tons. Add base materials separately — they add real tonnage the paver figure ignores.
2. Read your pickup's door-jamb payload sticker. GVWR minus curb weight is your true payload. A 3,060-lb Belgard Holland pallet overloads most half-ton trucks (~1,700 lb). Split loads or book delivery.
3. Confirm 10–12 ft of clear delivery access before scheduling. If the forklift can't reach the work area, the pallet stages at the curb and the 3,000+ lb becomes yours to hand-carry.
4. Apply a two-person carry for pieces at or above ~25 lb. Mega-Arbel (35–41 lb) and natural-stone slabs approach the ~51 lb NIOSH single-person guideline under field conditions. Never twist at the waist while holding a slab.
5. Size trucks against the upper bound of the pallet range. Published pallet weights carry ±5% regional-plant variance — plan to the top of the range so a heavy pallet doesn't put you over GVWR.

Common Paver Weight Mistakes

• Dividing a generic pallet weight by an assumed piece count. Pallet counts vary by product line (Belgard Holland 540 vs Pavestone Holland 480 at similar pallet weights), so a borrowed count throws the per-piece weight off by 10–15%. Pull the piece count from the actual product's cut-sheet before dividing pallet weight to estimate per-piece weight.
• Ignoring saturated weight. Concrete and especially clay and stone absorb water; a rain-soaked pallet or a wet install can run several percent heavier than the dry spec weight. Size delivery and lifting equipment with a small margin above the published dry figure, not right at it.
• Forgetting the base stack on an elevated deck. Homeowners size a rooftop or deck patio to the ~22–25 psf paver weight alone and skip the 4-in aggregate base that pushes the full stack to ~80–87 psf — roughly double a 40-psf residential benchmark. On any elevated surface, count the whole stack and get a structural engineer's review.

Frequently Asked Questions

How much does a concrete paver weigh?

A standard 4×8 inch concrete paver (60mm / 2.36 in thick) weighs approximately 4–6 lb, about 5–6 lb for a typical Belgard Holland Stone. Concrete pavers follow the ASTM C936 standard referenced in CMHA PAV-TEC-002; typical concrete density is ~130 lb per cubic foot. Large-format pieces like a Belgard Mega-Arbel (80mm, 15×21 in) weigh ~35–41 lb.

How much does a pallet of pavers weigh?

A full pallet of 60mm concrete pavers weighs roughly 2,900–3,100 lb: Belgard Holland Stone 540 pieces (120 sqft) at ~3,060 lb; Pavestone Holland 480 pieces (103 sqft) at ~2,884 lb; Cambridge 60mm lines ~2,095–2,715 lb. Use the upper bound of the range for truck-payload sizing to absorb ±5% regional plant variance.

How much does a paver weigh per square foot?

A 60mm concrete paver covers at about 22–25 lb per square foot, derived from a typical concrete density of ~130 lb per cubic foot for pavers built to the ASTM C936 standard referenced in CMHA PAV-TEC-002. At 4.5 pavers per square foot, a 200 sqft patio is ~900 pavers and ~4,500 lb (2.25 tons) of paver material — before base aggregate and sand.

Can I haul a pallet of pavers in my pickup truck?

A standard pallet at 2,900–3,100 lb exceeds most half-ton trucks (~1,700 lb payload per door sticker). A three-quarter-ton (~2,500 lb) is borderline and a one-ton (~3,500 lb) handles one full pallet. Split the load or book flatbed delivery with forklift offload; check your door-jamb GVWR sticker for your exact payload.

How much does a natural stone paver weigh?

Natural stone pavers (bluestone, granite) at 1.5–2 in thick weigh ~15–36 lb per piece — roughly 27–48 lb per square foot — because typical stone density (~160–175 lb per cubic foot) exceeds typical concrete density (~130 lb per cubic foot); concrete pavers themselves follow the ASTM C936 standard referenced in CMHA PAV-TEC-002. A single large slab can top the ~51 lb single-person handling guideline, so plan a two-person carry.

How many pavers are on a pallet?

Standard 60mm (4×8 in) concrete pavers run 480–540 pieces per pallet (103–120 sqft): Belgard Holland Stone 540, Pavestone Holland 480. Large-format Mega-Arbel (80mm, 15×21 in) runs ~72 pieces (78–104 sqft). Count varies by product line — confirm the current cut-sheet before using pallet weight to back into per-piece weight.

What is the heaviest paver I can safely lift by hand?

NIOSH's lifting equation puts the maximum recommended single-person load near 51 lb under ideal conditions. The industry-cited safe-handling guideline for loads over ~50 lb is a two-person carry. Standard 4×8 concrete pavers (4–6 lb) are easily solo; large-format and natural-stone pieces at 25–41 lb approach the two-person threshold once kneeling and twisting enter the picture.

Estimates only — verify with your local building authority and a qualified contractor before construction. See our full disclaimer.